SEAWIND 1190 SPORT SPECIFICATIONS

Overall Length

39 ft / 11.9 m

Beam

21'4" / 6.5 m

Draft

1' 11" / .6 m

Displacement

15,620 lbs / 6,600 kg

Diesel Saildrives

2 x 29 hp Yanmar

Fuel

71 US gal / 269 litres

Fresh Water

185 US gal / 700 litres

Steering Twin Helms

Cable Steering

Underwing Clearance

2’4" / 0.73 m

Mainsail

657 sq ft / 61 sq m

Jib

258 sq ft / 24 sq m

Screecher (optional)

603 sq ft / 56 sq m

Spinnaker (optional)

1,066 sq ft / 99 sq m

Overall Length

Beam

Draft

Displacement

Diesel Saildrives

Fuel

Fresh Water

Steering Twin Helms

Underwing Clearance

Mainsail

Jib

Screecher (optional)

Spinnaker (optional)

Seawind 1190 (11.9 METRES / 39ft )

STANDARD SPECIFICATIONS AND EQUIPMENT – OWNERS 3 Cabin Version

 

  1. GENERAL: 

The 1190 has been developed to meet the evolving needs of modern sailors. The 1190 offers a low maintenance high performing 39ft catamaran with enhanced upwind performance and shallow draft capability offered through retracting daggerboards. Perfect for weekend sails and a great base to begin your offshore cruising dream!

 

  1. EXTERIOR / LAMINATE:
  • Finish: Full female moulded hulls & decks, exterior gelcoat finish with molded-in non-slip surface on deck areas
  • Hull Laminate: Infused polyester resin laminate with vinylester tie layer
  • Hull Core Material: PVC closed cell foam core
  • Deck Laminate: Vacuum formed polyester resin laminate
  • Deck Core Material: PVC closed cell foam core
  • General Laminate: Vacuum formed polyester resin laminate
  • General Core Material: PVC closed cell foam core
  • Laminate specifications are certified to International CE standards
  1. MAST/BOOM/SAILS:
  • Clear anodized aluminium mast and boom. Single Spreader, 7/8 rig
  • Standing Rigging :

– Forestay 3/8 (10mm) 1 x 19 Dieform wire.

–  Sidestays 3/8 (10mm) 1 x 19 Dieform wire

–  Diamonds 5/16 (8mm) 1 x 19 Stainless Steel wire

  • Halyards:

– Main halyard:  12 mm Spectra rope : Heavy duty shackle

– Jib halyard:  8 mm Spectra rope. Heavy duty shackle

– Topping lift:  8 mm rope, Heavy duty shackle

– Boom outhaul: 10mm Spectra

  • Single line reefing, run to helm. Three reefing points with 2 reef lines

– Reef 1 & 3: 10mm rope. Leech/Clew blocks and snap shackle

– Reef 2: 10mm rope. Heavy duty shackle

  • Sheets:

– Main sheet: 10mm rope

– Main traveller: 8mm rope

– Jib sheet: 10mm rope

  • All halyards, reefing lines to be lead back to cockpit through turning blocks, rope clutches
  • Fully battened mainsail. Triple stitched reinforced construction. Leach adjustable batten end caps. Fibreglass sail battens
  • Mainsail cover with integrated lazy jack system.
  • Self-tacking headsail, curved headsail traveller track with end stops. With single line control sheet to cockpit.

 

  1. DECK EQUIPMENT:
  • Aluminium Hatches & portholes (9 in total)

– 4 x Forward Hatches 470mm x 470mm

– 2 x Mid cabin hatches 470mm x 470mm

– 1 x Port Bathroom window hatch 507mm x 377mm

– 1 x Galley window hatch 507mm x 377mm

– 1 x Aft Cabin window hatch 507mm x 377mm

  • Fibreglass Deck Hatches:

– 5 x Forward anchor & storage hatches

– 2 x Cockpit storage hatches

  • 6 x Docking cleats. Each side : bow, stern & amidships
  • 6 x Safety handles around cockpit
  • 1 x Heavy duty mooring cleat on forward walkway
  • Ventilation: 2 x forward cabin hatch vents
  • Mast base turning blocks. All halyards & sail controls to cockpit
  • 9x Rope clutches
  • Sheet winches : 2 x 45ST – 2 speed self tailing, 2 x 50ST – 2 speed self tailing
  • Stanchions/Rails: High quality stanchions, bow rails and stern rails with 3 life-lines.  With700mm high lifelines to meet CE requirements
  • 2 x transom access gates with pelican hook releases
  • 2 x side access gates with pelican hook releases
  • Aft swim ladder: folding stainless aft swim ladder

 

  1. FORWARD BEAM, CATWALK AND TRAMPOLINES:
  • Carbon reinforced fwd beam
  • Pelican striker and adjustable cable
  • 1 x Mooring plate above foredeck
  • 2 x Anchor roller under deck. Permanent stowage position for 45lb Plough (CQR/Delta type) anchor (cheeks 75mm high)
  • Catwalk in PVC foam-sandwich fibreglass
  • Light weight plastic coated open netted trampolines

 

  1. AFT BEAM AND DECK:
  • Targa Bar with curved mainsheet track and continuous line traveler control system
  • Stainless steel framed slatted seats behind aft beam
  • Full width hard top over cockpit

 

  1. STEERING SYSTEM:
  • Twin helm stations
  • 2 X 32” lightweight composite steering wheels
  • Both wheels independently linked to steering system. – system offers back-up redundancy
  • Retractable dagger boards below deck height when retracted
  • Lifting, transom hung rudders

 

  1. INTERIOR FINISH:
  • Furniture and cabin sides gloss gelcoat finish
  • Cabin top lined with light weight internally molded gelcoat liner
  • Floors: synthetic timber flooring
  • Lightweight cupboard doors and trimmings
  1. SALOON:
  • Lightweight handcrafted saloon table
  • Upholstered settee
  • Lightweight handcrafted coffee table
  • Forward aluminium opening windows
  • Saloon side windows in 8mm toughened glass
  • Tri folding cockpit doors
  • Removable low profile, helm hatches

 

  1. GALLEY:
  • Spacious galley with coordinated Polystone counter surfaces
  • Three (3) burner LPG stove, stainless steel pot holders. Flame failure device to shut off LPG immediately in event of flame going out
  • Double bowl stainless steel sink
  • Pressure fresh water system
  • Refrigerator: Front opening upright fridge with freezing compartment 80 litres
  • Under bench storage
  • Trash bin
  • LPG solenoid control in galley

 

  1. SLEEPING CABINS:
  • Light weight PVC foam cored doors on all private cabins
  • Port & Starboard fwd cabins : Each queen sized bed (2050mm x 1540mm)
  • Aft Starboard cabin : Double bed (1990mm x 1230mm)
  • Mattresses 150mm ( 6” ) foam upholstered
  • Cabins lined
  • 12volt LED lighting
  • Storage/Cupboards

 

  1. PORTHEAD:
  • Polished light weight PVC foam cored door
  • Manual toilet. Discharge via holding tank
  • Holding tank built in. Discharge pump out by shore station or directly overboard 130L
  • Pipes, skin fittings and sea-cocks are easily accessible and to meet survey requirements
  • Vanity basin with pressure water
  • Separate shower stall with wall mounted shower head & mixer tap
  • Electric shower bilge pump with direct overboard discharge
  • Large quantity cupboards / shelves to very high quality

 

  1. LIGHTING/ELECTRICAL SYSTEM:
  • High quality DC electrical switch panel with circuit breakers, LED indicator lights and voltage display
  • Marine grade tinned electrical wiring with extensive use of heat sealed connectors
  • Batteries x 2 comprising House System (270 amp hrs). One engine cranking battery – 130 amp hr heavy duty battery
  • 230amp heavy duty isolation switch
  • 12V lighting : Numerous 12V interior lamps and courtesy lights throughout including recessed lights in cockpit
  • 4 x 12V Outlets
  • CE approved navigation lights. Port & Starboard mounted on bow rails
  • Deck floodlight mounted on spreaders
  • Mast head anchor / riding light.

 

  1. PUMBING /FRESH WATER TANKS:
  • Pressure water system with water to galley and bathroom
  • Fresh water tank: 700 litres( 185gallons) rotomoulded. Remote deck filler
  • Electric fresh water pump
  • Electric bilge pumps (2) with controls integral with master battery switch panel
  • Manual bilge pumps (2) in each hull
  • Marelon through-hull fittings to CE/ISO standard
  • Manual toilet in head
  • 1 x LPG bottle – 4.5kg
  • Fresh water tank gauge

 

  1. ENGINES:
  • Twin lightweight Honda 20hp 20” engines. Mounted under each helm seat at each steering station
  • 5” leg extensions added to engines to reduce cavitation
  • Remote electric key start with electric tilt fitted
  • Dual engine controls at port helm station
  • 270l fuel tank mounted in external locker fwd of mast

 

  1. NAVIGATION:
  • Twin steering compasses

 

  1. ANCHORING /MOORING:
  • Primary anchor is 45 lb CQR anchor type with 55 mtrs x 8mm short link galvanised chain and 40 mtrsx 16mm triple braid anchor warp
  • Primary anchor is stored in a specially designed anchor roller under the forward beam
  • 3 x PVC Inflatable Fenders
  • 3 x Mooring lines (each 15 metres x 14mm)

 

  1. ANTIFOULING / STRIPING:
  • Epoxy barrier coat plus 2 coats of high quality black antifouling bottom paint
  • Seawind 1190 decal on each hull and stern

 

 

DISCLAIMER: The specifications above may change at Seawind Catamaran’s discretion.